Available on backorder
Mauch 082: 2-6S BEC HS-series in India
₹1,699.00
Description: Input 2-6S LiPo / max. 28V. Output 5.35V / 3A -> +/- 0.05V –> Ripple 10mV (0.2%) at 1.5A output current. Input wrong polarity...
Add to cart
Available on backorder
Mauch 085: 4-14S BEC (HS) for pixhawk 2.1 in India
₹4,200.00Short Description :
- Output 5.3V / 3A -> +/- 0.05V.
- Input 4-14S LiPo / max. 60V.
Available on backorder
Mauch 083: 2-6S Backup BEC (HS) for Pixhawk 2 in India
₹4,000.00Short Description :
- Output 5.35V / 3A -> +/- 0.05V –> Ripple 10mV (0.2%) at 1.5A output current.
- Input 2-6S LiPo / max. 28V.
Available on backorder
Mauch 076: HS-200-HV ,200A Sensor in India
₹6,000.00Short Description :
- 200A - Current measurement sensor board, based on Allegro Hall Sensor ACS-200U.
- This Sensor board needs a power supply. So please select the matching BEC according your preference from the BEC section.
Available on backorder
Mauch 075 : HS-200-LV , 200A Sensor in India
₹6,000.00Short Description :
- 200A - Current measurement sensor board, based on Allegro Hall Sensor ACS-200U.
- The BEC will also power the flight controller as well as the attached equipment like GPS, telemetry... etc.
Available on backorder
Mauch 074: HS -100-HV , 4-14S Sensor in India
₹4,000.00Short Description:
- 100A - Current measurement sensor board, based on Allegro Hall Sensor ACS-100U.
- This Sensor board needs a power supply. So please select the matching BEC according your preference from the BEC section.
Available on backorder
Mauch 073: HS-100-LV Sensor in India
₹3,789.00
Short Description :
Add to cart
- 100A - Current measurement sensor board, based on Allegro Hall Sensor ACS-100U.
- This Sensor board needs a power supply. So please select the matching BEC according your preference from the BEC section
Available on backorder
Available on backorder
004: PL-200/8 Sensor Board with CFK enclosure in India
₹6,000.00-
200A Hall Effect Current Sensor (ACS770-250U)
-
Supports up to 14S (60V) voltage monitoring
-
Direct connection to Mauch Premium-Line BECs & Sensor Hub X2-V2
-
Durable CFK (carbon fiber composite) enclosure
-
Pre-attached 2x 15cm 8AWG wires for easy setup
-
Molex Clik-Mate 4-pin (5023800400) connector for clean integration
-
Delivered in a protective PP box (55 x 55 x 20mm)
Available on backorder
MAUCH 021: PL 4-14S HYB-BEC / 1x 5.3V For UAV /Drones in India
₹7,500.00Product description:
.Output 5.30V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current. . Delivery in PP box: 55 x 55 x 20mm . 1x 021: PL 4-14S HYB-BEC / 1x 5.3V / 3A . 1x 040: PL - Series sensor cable / L=150mmAvailable on backorder
Mauch 010: PL Sensor Hub X2-V2 with CFK enclosure for UAV/DRONES in India
₹5,800.00- This sensor hub allows to connect two PixHawk Mauch current sensors in parallel in order to add their current capacities.
- The current of both sensors is summarized before reaching the flight controller while the voltage measurement of the LiPo packs are collected from both sensors and passed through the hub to the flight controller.
- The main purpose of this hub is to replace existing protection circuits and to monitor that both paralleled LiPos are supplying the same current to the system.
- Thanks to Mauch Sensor Hub X2, you can spot early when a LiPo starts to fail, way before this situation is irreversible.
- In case of difference in current is of +/- 15%, the alarm output goes ON in order to indicate the fault. The pilote should then land immediately in order to check the batteries.
Available on backorder
Mauch 017: PL 4-6S BEC 2×5.35V 1×12.0V with CFK enclosure in India
₹6,499.00
Input 4-6S LiPo / max. 28V. Output 2x 5.35V / 3A + 1x 12.0V / 3A -> +/- 0.05V –> Ripple 10mV (0.2%) at 1.5A...
Add to cart